Human motion capture from monocular videos has made significant progress in recent years. However, modern approaches often produce temporal artifacts, e.g. in form of jittery motion and struggle to achieve smooth and physically plausible motions. Explicitly integrating physics, in form of internal forces and exterior torques, helps alleviating these artifacts. Current state-of-the-art approaches make use of an automatic PD controller to predict torques and reaction forces in order to re-simulate the input kinematics, i.e. the joint angles of a predefined skeleton. However, due to imperfect physical models, these methods often require simplifying assumptions and extensive preprocessing of the input kinematics to achieve good performance.

This paper studies the experimental comparison of two different whole-body control formulations for humanoid robots: inverse dynamics whole-body control (ID-WBC) and passivity-based whole-body control (PB-WBC). The two controllers fundamentally differ from each other as the first is formulated in task acceleration space and the latter is in task force space with passivity considerations. Even though both control methods predict stability under ideal conditions in closed-loop dynamics, their robustness against joint friction, sensor noise, unmodeled external disturbances, and non-perfect contact conditions is not evident. Therefore, we analyze and experimentally compare the two controllers on a humanoid robot platform through swing foot position and orientation control, squatting with and without unmodeled additional weights, and jumping. We also relate the observed performance and characteristic differences with the controller formulations and highlight each controller's advantages and disadvantages.

Bipedal locomotion makes humanoid robots inherently prone to falls, causing catastrophic damage to the expensive sensors, actuators, and structural components of full-scale robots. To address this critical barrier to real-world deployment, we present \method, a framework that learns to predict imminent, unavoidable falls and execute protective maneuvers to minimize hardware damage. SafeFall is designed to operate seamlessly alongside existing nominal controller, ensuring no interference during normal operation. It combines two synergistic components: a lightweight, GRU-based fall predictor that continuously monitors the robot's state, and a reinforcement learning policy for damage mitigation. The protective policy remains dormant until the predictor identifies a fall as unavoidable, at which point it activates to take control and execute a damage-minimizing response. This policy is trained with a novel, damage-aware reward function that incorporates the robot's specific structural vulnerabilities, learning to shield critical components like the head and hands while absorbing energy with more robust parts of its body. Validated on a full-scale Unitree G1 humanoid, SafeFall demonstrated significant performance improvements over unprotected falls. It reduced peak contact forces by 68.3\%, peak joint torques by 78.4\%, and eliminated 99.3\% of collisions with vulnerable components. By enabling humanoids to fail safely, SafeFall provides a crucial safety net that allows for more aggressive experiments and accelerates the deployment of these robots in complex, real-world environments.

In-Situ Resource Utilization (ISRU) is one of the key technologies for enabling sustainable access to the Moon. The ability to excavate lunar regolith is the first step in making lunar resources accessible and usable. This work presents the development of a bucket drum for the modular robotic system MoonBot, as part of the Japanese Moonshot program. A 3D-printed prototype made of PLA was manufactured to evaluate its efficiency through a series of sandbox tests. The resulting tool weighs 4.8 kg and has a volume of 14.06 L. It is capable of continuous excavation at a rate of 777.54 kg/h with a normalized energy consumption of 0.022 Wh/kg. In batch operation, the excavation rate is 172.02 kg/h with a normalized energy consumption of 0.86 Wh per kilogram of excavated material. The obtained results demonstrate the successful implementation of the concept. A key advantage of the developed tool is its compatibility with the modular MoonBot robotic platform, which enables flexible and efficient mission planning. Further improvements may include the integration of sensors and an autonomous control system to enhance the excavation process.

Neural surrogates and operator networks for solving partial differential equation (PDE) problems have attracted significant research interest in recent years. However, most existing approaches are limited in their ability to generalize solutions across varying non-parametric geometric domains. In this work, we address this challenge in the context of Polyethylene Terephthalate (PET) bottle buckling analysis, a representative packaging design problem conventionally solved using computationally expensive finite element analysis (FEA). We introduce a hybrid DeepONet-Transolver framework that simultaneously predicts nodal displacement fields and the time evolution of reaction forces during top load compression. Our methodology is evaluated on two families of bottle geometries parameterized by two and four design variables. Training data is generated using nonlinear FEA simulations in Abaqus for 254 unique designs per family. The proposed framework achieves mean relative $L^{2}$ errors of 2.5-13% for displacement fields and approximately 2.4% for time-dependent reaction forces for the four-parameter bottle family. Point-wise error analyses further show absolute displacement errors on the order of $10^{-4}$-$10^{-3}$, with the largest discrepancies confined to localized geometric regions. Importantly, the model accurately captures key physical phenomena, such as buckling behavior, across diverse bottle geometries. These results highlight the potential of our framework as a scalable and computationally efficient surrogate, particularly for multi-task predictions in computational mechanics and applications requiring rapid design evaluation.

Abstract--A force balanced manipulator design based on the closed chain planar five bar linkage is developed and experimentally validated. We present 2 variants as a modular design: Forbal-2, a planar 2-DOF manipulator, and its extension to 5-DOF spatial motion called Forbal-5. The design considerations in terms of geometric, kinematic, and dynamic design that fulfill the force balance conditions while maximizing workspace are discussed. Then, the inverse kinematics of both variants are derived from geometric principles. The results show how the balanced configuration yields a reduction in the average reaction moments of up to 66%, a reduction of average joint torques of up to 79%, as well as a noticeable reduction in position error for Forbal-2. For Forbal-5, which has a higher end effector payload mass, the joint torques are reduced up to 84% for the balanced configuration. Experimental results validate that the balanced manipulator design is suitable for applications where the reduction of joint torques and reaction forces/moments helps achieve millimeter level precision. Robot manipulators are now increasingly part of industrial automation, forming the bedrock of modern manufacturing processes.

In this letter, we present tightly coupled LiDAR-IMU-leg odometry, which is robust to challenging conditions such as featureless environments and deformable terrains. We developed an online learning-based leg kinematics model named the neural leg kinematics model, which incorporates tactile information (foot reaction force) to implicitly express the nonlinear dynamics between robot feet and the ground. Online training of this model enhances its adaptability to weight load changes of a robot (e.g., assuming delivery or transportation tasks) and terrain conditions. According to the \textit{neural adaptive leg odometry factor} and online uncertainty estimation of the leg kinematics model-based motion predictions, we jointly solve online training of this kinematics model and odometry estimation on a unified factor graph to retain the consistency of both. The proposed method was verified through real experiments using a quadruped robot in two challenging situations: 1) a sandy beach, representing an extremely featureless area with a deformable terrain, and 2) a campus, including multiple featureless areas and terrain types of asphalt, gravel (deformable terrain), and grass. Experimental results showed that our odometry estimation incorporating the \textit{neural leg kinematics model} outperforms state-of-the-art works. Our project page is available for further details: https://takuokawara.github.io/RAL2025_project_page/

Human motion capture from monocular videos has made significant progress in recent years. However, modern approaches often produce temporal artifacts, e.g. in form of jittery motion and struggle to achieve smooth and physically plausible motions. Explicitly integrating physics, in form of internal forces and exterior torques, helps alleviating these artifacts. Current state-of-the-art approaches make use of an automatic PD controller to predict torques and reaction forces in order to re-simulate the input kinematics, i.e. the joint angles of a predefined skeleton. However, due to imperfect physical models, these methods often require simplifying assumptions and extensive preprocessing of the input kinematics to achieve good performance.

An uneven shell surface enables steering by using only the movement of the pendulum, allowing for mechanically simple designs that may be feasible to scale to large quantities or small sizes. We train a control policy using reinforcement learning in simulation and deploy it onto the robot to complete a rectangular trajectory. I. INTRODUCTION A. Motivation Existing spherical robot designs require two to four actuators for steering and jumping capabilities [1], increasing cost, power use, maintenance, and size. Reducing the number of actuators can alleviate these challenges, making it easier to scale to greater numbers and smaller sizes. This work investigates ROCK, a robot with an internal pendulum controlled by a single motor capable of rolling, steering, and jumping.

Traditional constitutive models rely on hand-crafted parametric forms with limited expressivity and generalizability, while neural network-based models can capture complex material behavior but often lack interpretability. To balance these trade-offs, we present Input-Convex Kolmogorov-Arnold Networks (ICKANs) for learning polyconvex hyperelastic constitutive laws. ICKANs leverage the Kolmogorov-Arnold representation, decomposing the model into compositions of trainable univariate spline-based activation functions for rich expressivity. We introduce trainable input-convex splines within the KAN architecture, ensuring physically admissible polyconvex hyperelastic models. The resulting models are both compact and interpretable, enabling explicit extraction of analytical constitutive relationships through an input-convex symbolic regression techinque. Through unsupervised training on full-field strain data and limited global force measurements, ICKANs accurately capture nonlinear stress-strain behavior across diverse strain states. Finite element simulations of unseen geometries with trained ICKAN hyperelastic constitutive models confirm the framework's robustness and generalization capability.